When using the brewing equipment, you must not panic if the brewing equipment has shutdown failure. This is actually some common problems in the use of many equipment. Let me tell you this.

1.立即关闭酿酒设备的料斗门，尽可能挤出桶内多余的物料；切断电源和水源，取下模具上的加热元件，然后取下模具，然后用专用工具取下螺钉。如果要生产聚烯烃材料，不得拆卸螺钉。但是，如果出现严重的机械故障，一般很难在短时间内恢复生产，将螺钉取出进行清洗。

1. Immediately close the hopper door of the brewing equipment and squeeze out the excess materials in the barrel as much as possible; Cut off the power and water supply, first remove the heating element on the die, then remove the die, and then remove the screw with a special tool. If polyolefin material is to be produced, the screws must not be removed. However, in case of serious mechanical failure, it is generally difficult to resume production in a short time. Take out the screws for cleaning.

2.用铜或铝工具清洗螺杆、机筒和模具，并仔细检查零件表面是否有磨损和伤痕。如果有的话，用油石仔细打磨。酿酒设备安装模具的压盖也应仔细打磨。

2. Clean the screw, barrel and die with copper or aluminum tools, and carefully check whether there are wear and scars on the surface of parts. If any, polish it carefully with an oilstone. The gland of the installation mould of brewing equipment shall also be carefully polished.

3.如果酿酒设备按上述方法清理后没有启动，检查临时停机的原因。如果不能立即恢复生产，应先用油脂垂直悬挂螺钉，然后再安排故障排除和维修。设备修补后，重新安装螺杆，在用于安装模具的螺栓上涂抹耐高温油脂，然后安装模具。螺栓应该对角拧紧。如果条件允许，使用扭矩扳手，以确保模具不会泄漏，并且再次拆卸非常方便。

3. If the brewing equipment is not started after cleaning according to the above methods, first check the causes of temporary shutdown. If production cannot be resumed immediately, hang the screws vertically with grease first, and then arrange troubleshooting and maintenance. After the equipment is repaired, reinstall the screw, apply high-temperature grease on the bolts used to install the mold, and then install the mold. Bolts should be tightened diagonally. If conditions permit, use a torque wrench to ensure that the die will not leak and it is very convenient to disassemble again.

4.由于酿酒过程没有得到很好的控制，因此有必要找出酿酒设备操作过程失控的原因并加以。例如，是因为温度控制仪表出了故障还是热电偶没有正确插入。

4. Because the brewing process is not well controlled, it is necessary to find out the causes of out of control in the operation process of brewing equipment and solve them. For example, is it because the temperature control instrument fails or the thermocouple is not inserted correctly.

以上就是酿酒设备停机时我们应该做的。正确的预防和有用的维护是提高酿酒设备使用效率的基本保证。对于酿酒设备的突然关机，虽然出现不多，但也不能忽视。

The above is what we should do when the brewing equipment is shut down. Correct prevention and useful maintenance are the basic guarantee to improve the use efficiency of brewing equipment. The sudden shutdown of brewing equipment is rare, but it can not be ignored.